Study of equivalent efficiency calibration method for radioactive gas source measured on HPGe detectors

ABSTRACT

In view of the complexity of current detection efficiency calibration of radioactive gas sources, a method using solid planar sources to be equivalent to gas sources was studied. For the 50 mL gas source box, an optimal equivalent scheme was selected by Monte Carlo Simulations. Then, the full-energy-peak efficiency curve of gas sources at the measurement position of 25 cm, with source-to-detector distance of 25 cm, was fitted by measuring solid planar sources with known activity. To verify the accuracy of the efficiency curve, ⁴¹Ar, ¹³³Xe and ⁸⁷Kr gases were produced and determined by length-compensated method. Then, their full-energy-peak efficiencies at 25 cm position away from the detector were directly calibrated. The percentage efficiency deviations between interpolation from the efficiency curve and direct calibration are all less than 2.5%, which proves the accuracy of the equivalent method. This calibration method is a general one and can be also used for some other radioactive sample measurements, such as non-destructive analysis of gaseous fission product samples with a suitable source-to-detector distance.     

基于金属基复合材料的硅通孔热应力仿真分析

硅通孔(TSV)技术是三维集成电路中的关键技术,对信号传输以及热量的传导起到关键的作用,其热可靠性的问题一直都是研究热点。基于Comsol Mulitiphsics平台,通过有限元仿真分析,研究了金属基复合材料对TSV热应力的影响。并进一步研究了在不同通孔直径以及不同TSV高度下,碳纳米管(CNTs)、碳纳米管铝(CNTs/Al)以及碳纳米纤维铜(CNFs/Cu)等复合材料和传统金属材料的等效热应力情况。结果表明:与传统金属材料相比,金属基复合材料CNTs/Al以及CNFs/Cu均能有效降低TSV的热应力,提高TSV的热可靠性;并且对于CNTs含量不同的金属基复合材料,其TSV的等效热应力也会有所不同,需综合考虑合理选择CNTs的含量。     

Evaluation of electrochemical properties of antibacterial ZnO layers deposited to 316LVM steel using atomic layer deposition

The presence of a biofilm can lead to the disappearance of the surrounding bone tissue and, as a result, disturb the osseointegration process. Unfortunately, both in the case of instability of the implant and long-term bacterial infections, there is often a need for reoperation as well as replacement of the implant, which in turn is associated with huge costs, but most of all discomfort for the patient associated with long-term hospitalization. In order to limit this unfavorable process, the physicochemical properties of the surface layer of implants are indicated. Therefore, the paper proposes applying a layer with antibacterial effect on the surface of 316LVM steel used in bone surgery. As part of the work, the ZnO layer was applied using the atomic layer deposition method with different parameters of the application process (different number of cycles at constant temperature). In the first stage, pitting corrosion resistance tests were carried out using the potentiodynamic method and studies using electrochemical impedance spectroscopy. The surface morphology tests using a scanning electron microscope were also complemented. Obtained results may form the basis for the development of more detailed criteria for the assessment of the final quality of medical devices used in the skeletal system.     

组合形活塞销冷镦挤成形工艺

针对组合形活塞销结构特征和工艺要求,分析该零件的成形难点为:两端圆锥孔的挤压成形和深径比大于2. 5的中心圆孔反挤压。为此,应用DEFORM-2D有限元分析软件对组合形活塞销7工位冷镦挤成形工艺进行数值模拟分析。通过数值模拟分析和工艺方案修订,确定最终的成形工艺方案为:下料-整形-压凹-反挤压-冲孔-第1次挤锥-第2次挤锥,并采用硬质合金YG15制造反挤压凸模,以避免一次反挤压成形时凸模横截面变化处的折断。采用该方案进行工艺实验,实验结果表明:组合形活塞销尺寸满足零件设计要求,无折叠、开裂等锻造缺陷,深孔反挤压凸模使用寿命大于8万件。     

质子交换膜燃料电池电化学阻抗谱弛豫时间分布研究

电化学阻抗谱技术能够获取燃料电池不同频率阻抗，但对阻抗的构成缺乏进一步解析，难以直接构建精准的等效电路模型进行阻抗拟合分析，而弛豫时间分布（Distribution of relaxation time，DRT）方法不需要定义特定的等效电路模型，即可解析燃料电池不同时间常数的极化过程。针对实验室用质子交换膜燃料电池，在不同运行条件下对其进行阻抗谱测量，并通过Kramers-Kronig关系验证所记录阻抗数据的质量。基于DRT分析方法，系统地解释阻抗谱中各频段阻抗对应的物理或化学意义。研究表明，该电池的电化学阻抗谱主要由3个不同时间常数频段的极化阻抗构成，通过与运行条件相关性的系统分析，确定低频段阻抗为氧气在多孔介质中的传输阻碍，中频段阻抗为与氧还原反应有关的电荷传递阻碍，中高频段阻抗为阴极催化剂层中的质子传输阻碍。为进一步确定DRT分析结果的合理性，采用等效电路模型拟合测量的阻抗数据，辨识的电阻元件参数变化趋势与DRT分析结果一致。     

高速列车转向架构架损伤、等效应力及寿命分布特性研究

为分析高速列车转向架构架损伤、等效应力及寿命分布特性，对构架疲劳关键测点进行动应力线路实测并对测点实测时域数据波形进行解析；基于实测应力时间历程及雨流计数法编制二维应力谱，利用Goodman等寿命方程将二维应力谱等效转换为一维应力谱；阐述线性累积损伤及非线性累积损伤模型的建立方法并对实测数据的线性累积损伤及非线性累积损伤进行了计算及对比分析；分别基于线性累积损伤理论及非线性累积损伤理论推导出各理论下的等效应力，基于实测数据对两种等效应力进行了计算及对比分析；通过结合非线性累积损伤及线性累积损伤理论计算的等效应力及不同可靠度下的材料S-N曲线计算并对比分析构架结构的疲劳寿命。研究结果表明，与非线性疲劳分析理论相比，线性疲劳分析理论对高速列车转向架构架的疲劳特性评估偏于保守。     

基于流固耦合的柱面气膜密封支撑结构性能研究

利用流固耦合分析方法,研究一种波箔结构柔性支撑柱面气膜密封,探讨气膜厚度、浮环与转子的偏心率以及柔性支撑结构的泊松比、弹性模量、波箔数量等参数对支撑结构等效应力及变形量的影响。结果表明:柔性支承结构满足柱面气膜密封的正常运作,不会造成因为气膜刚度过大而使得浮环与波箔发生破坏性变形,并且变形量远小于波箔高度;柔性支撑的等效应力和变形量随平均气膜厚度的增大而减小,随偏心率的增加而增大,随支撑材料泊松比的增大而增大;弹性模量的增加并不影响柔性支撑结构的等效应力,但是会使变形量减小;增加波箔数量,柔性支撑的等效应力略有减小,变形量显著减小。     

被动湍流控制圆柱驰振能量收集的等效电路研究

为更好的预测驰振压电能量收获机的性能,首先建立了等效电路仿真模型(ECM)并通过实验验证,最大误差不超过10%。采用该方法分析了被动湍流控制(PTC)下圆柱驰振压电能量收集的仿真模型,且该方法可将驰振能量转化系统的质量-弹簧-阻尼(M-C-K)控制方程中各参数用等效电路的电子元件来表示,从而可以分析过往仿真手段所不能解决的直流电路耦合问题。其次,从能量收集效率角度分析了交流-直流等效电路中临界风速(Ucr)随外接载荷的变化规律,及输出电压与功率随不同风速和外界载荷的变化规律。结果表明,交流电路中Ucr随载荷的增大先增大后减小,直流电路中Ucr随载荷的增大逐渐减小。当风速达到Ucr的最大值时,驰振在任一电阻下均会发生。U≥Ucr时,驰振出现锁定现象,输出电压和功率均随着风速的增大而增大。当风速过大时,增长率有减小趋势。输出电压均随着电阻的增大而增大,功率随电阻的增大先增大后减小。相比于交流电路,直流电路的最佳负载由1.1 MΩ提高到2.0 MΩ,同时功率峰值从0.08 mW降低到0.04 mW。     

Electrochemical corrosion behavior of LDX 2101® duplex stainless steel in a fluoride-containing environment

The effect of fluoride on the electrochemical corrosion behavior of an LDX 2101® duplex stainless steel (DSS) was studied. Open-circuit potential (E_OC) and electrochemical impedance spectroscopy (EIS) measurements were carried out in artificial saliva and with the addition of fluoride (1 wt% NaF). The electrochemical corrosion behavior of the AISI 316L austenitic stainless steel (SS) was also evaluated for comparison. Both open-circuit potential and EIS results indicate that DSS and austenitic SS undergo spontaneous passivation due to spontaneously formed oxide film passivating the metallic surface, in the simulated aggressive environments. However, LDX 2101® exhibits superior corrosion resistance as compared with AISI 316L, and this improvement is ascribed to the formation of a passive film which shows a higher protective effect than the one formed on AISI 316L.